Land Grader Customizable Fast delivery speed-manufacture,factory,supplier from China

During the operation of the automatic feeding corn thresher, the speed of the car must not be too fast or too slow, otherwise it is easy to block the feed inlet, feed evenly, such as uneven can lead to broken CORNCOB, low yield, plug.Troubleshooting: 1. the front hopper down rollers too close to the ground, resulting in large angle iron scraping. 2. If the band is too loose, adjust the roller upwards to reinstall the band. 3. the clutch is too loose, the Clutch U Card to the outside loose a few silk solution. 4.

1. At the beginning of the work, the Rototiller should be in the state of lifting, first combined with the power output shaft, so that the rotation speed of the cutter shaft increased to the rated speed, and then decreased the Rototiller, so that the blade gradually buried to the required depth. It is forbidden to combine the blade with the power output shaft or down the Rototiller after the blade is buried, so as not to cause the blade to bend or break and increase the load of the tractor. 2.

I. Adjustment of tillage depth of deep ploughing plough:Generally speaking, the tillage depth of deep ploughs should not be less than 10cm. Rotary tiller matched with walking tractor can adjust the depth of cultivated land by changing the height of tail wheel. When adjusting, just turn the adjusting handle.The ploughing depth is controlled by the hydraulic system of the deep ploughing machine matched with the wheeled tractor.

 5TY Series Corn Thresher, when working, the corn is fed by the feed mouth, the corn is hit in the high speed rotating rotor and the drum, the kernel is separated by the sieve hole, the corn core is discharged from the tail of the machine, the corn silk, the skin is discharged from the tuyere. The feed hole is arranged on the upper cover of the machine. The corn stick enters the threshing chamber through the feed hole. The corn grains are knocked off by the high-speed rotating rotor in the threshing chamber and separated through the sieve holes.

(1)High hardness discs with 65Mn Spring steel material make perfect soil deep cultivating. (2)The plough discs are rotated during work, no entangle the grass and no block(3)Surface sprayed treatment, beautiful appearance, not easy to fade(4)Widely applications for cultivated or hard land, universally used for 60hp to 160hp tractors(5)Strong construction, big bolts and nuts, high quality spare parts, resonable design make this plough excellent work and long service life. 

The working part is a Rotary Tiller with 2 ~ 3 spiral cutters. During the operation, the Rotary Tiller rotates around the vertical axis and the cutter cuts the soil into pieces. The utility model is suitable for paddy field hydroponic cultivation, and has strong soil crushing and pulp action, but poor covering performance. Used more in Japan. In order to enhance the effect of Rototiller, various additional devices have been installed on the rototiller in some countries.

Rotary tillage part is the most commonly used tillage part of micro-tiller, and the engine power drives the rotary tillage cutter shaft to rotate through the transmission device. Rotary tillage knife shaft is horizontally arranged, and several rotary tillage blades are arranged on the circumference of the knife shaft. The transmission of the knife shaft has two forms: middle transmission and side transmission.

Potato harvesters are a outstanding manner to store guide labour throughout potato harvest. Before the discovery of the potato harvester, maximum human beings dug their potatoes from the floor the use of a fork or a spade. Then they lifted the potatoes from the floor and positioned them right into a basket earlier than tipping them right into a hessian fabric bag to be stored. Potatoes are commonly grown in drills or beds, this facilitates the harvester dig a good width of soil and potatoes because it movements alongside the field.

Supplying high quality harrow and plough's spare parts, including discs, hubs, bearings, spacers, harrow shafts etc. We can also customize the parts according to sample or drawing. 

What is a disc plough used for?The disc plough is designed to work in all types of soil for functions such as soil breaking, soil raising, soil turning and soil mixing. It is used to open the new fields and to process the stony areas. It can be used easily at rocky and rooted areas.