Rotary Tiller Subsoiler machine Customizable fast delivery speed-manufacture,factory,supplier from China

It's been around since 1805, when lawn mowers were manual and had no power support.In 1805, Plucknett, an Englishman, invented the first machine to harvest grain and cut weeds. People pushed the machine and drove the rotary knife to cut grass through gear transmission.

Rotary tillage part is the most commonly used tillage part of micro-tiller, and the engine power drives the rotary tillage cutter shaft to rotate through the transmission device. Rotary tillage knife shaft is horizontally arranged, and several rotary tillage blades are arranged on the circumference of the knife shaft. The transmission of the knife shaft has two forms: middle transmission and side transmission.

I. Adjustment of tillage depth of deep ploughing plough:Generally speaking, the tillage depth of deep ploughs should not be less than 10cm. Rotary tiller matched with walking tractor can adjust the depth of cultivated land by changing the height of tail wheel. When adjusting, just turn the adjusting handle.The ploughing depth is controlled by the hydraulic system of the deep ploughing machine matched with the wheeled tractor.

 5TY Series Corn Thresher, when working, the corn is fed by the feed mouth, the corn is hit in the high speed rotating rotor and the drum, the kernel is separated by the sieve hole, the corn core is discharged from the tail of the machine, the corn silk, the skin is discharged from the tuyere. The feed hole is arranged on the upper cover of the machine. The corn stick enters the threshing chamber through the feed hole. The corn grains are knocked off by the high-speed rotating rotor in the threshing chamber and separated through the sieve holes.

1. The liquid medicine box has large capacity, long spraying time and high working efficiency. 2. The liquid pump of the spraying machine adopts multi-cylinder diaphragm pump, which has large displacement and reliable operation. 3. The spray bar adopts single-point hanging balance mechanism, which has good balance effect. 4. The spray bar adopts the pull-rod turntable folding mechanism. The lifting, unfolding and folding of the spray bar can be controlled by operating the hydraulic cylinder in the cab, which is convenient and labor-saving. 5.

The working part is a Rotary Tiller with 2 ~ 3 spiral cutters. During the operation, the Rotary Tiller rotates around the vertical axis and the cutter cuts the soil into pieces. The utility model is suitable for paddy field hydroponic cultivation, and has strong soil crushing and pulp action, but poor covering performance. Used more in Japan. In order to enhance the effect of Rototiller, various additional devices have been installed on the rototiller in some countries.

During the operation of the automatic feeding corn thresher, the speed of the car must not be too fast or too slow, otherwise it is easy to block the feed inlet, feed evenly, such as uneven can lead to broken CORNCOB, low yield, plug.Troubleshooting: 1. the front hopper down rollers too close to the ground, resulting in large angle iron scraping. 2. If the band is too loose, adjust the roller upwards to reinstall the band. 3. the clutch is too loose, the Clutch U Card to the outside loose a few silk solution. 4.

1. At the beginning of the work, the Rototiller should be in the state of lifting, first combined with the power output shaft, so that the rotation speed of the cutter shaft increased to the rated speed, and then decreased the Rototiller, so that the blade gradually buried to the required depth. It is forbidden to combine the blade with the power output shaft or down the Rototiller after the blade is buried, so as not to cause the blade to bend or break and increase the load of the tractor. 2.

This baldan disc plough is very popular by customers and widely application.It is standard 3 point linkage with four wheel tractors from 60hp to 160hp. The discs are rotary motion when tuning the soil.

This 3QL series agriculture equipment furrow ridger gadget tractor ridger is suitable for ridging after the tillage in the farm area. It includes heavy duty tubular field body, the complete device is made a lot stronger than everyday ones. This ridger is suitable for ridging after the tillage inside the field for potato, beans, vegetable etc.It is convenient to regulate the ridging top and the ridging rows and space between every ridge. It could be effortlessly spaced (widened or narrowed) consistent with the crop requirement. The rubber tires may be moved without problems.